Each person has got their personal opinion when it comes to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Setting up a tub isn't exactly brain surgery, yet it does call for strong plumbing, carpentry, as well as in some cases, tiling skills. Changing an old bath tub with a brand-new one is also a moderately hard job. If the old tub is easily accessible, the project can move quickly; if you have to open up a wall to remove the old bathtub and also position the brand-new tub, the task is a lot harder. In either situation, the task is within a home handyman's abilities, although you will need a helper to move out the old tub and also embeded in the new one. Make sure you have qualified on your own for the task and fit attempting it. Instead of employing a specialist to take control of a halfway-completed project, it is better to think about employing one before you start. Chances are you might require a specialist plumber to make tube connections.
This article will assist you set up a brand-new bath tub in your bathroom if you have actually already bought a new tub and do not need to change the setup of your previous supply of water pipes.
Your tools and material list must consist of the following:
Removing Old Touches
If you need to replace old taps with new ones as a part of your installation, after that the first thing you need to do is detach the water. After doing so, switch on the faucets to drain pipes any type of water continuing to be in the system. The process of removing the existing taps can be fairly bothersome due to the limited accessibility that is typically the case.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the taps. Have a cloth all set for the remaining water that will certainly originate from the pipelines. When the supply pipes have been removed, utilize the very same tool to loosen the nut that holds the taps onto the bath/basin. You will require to stop the single taps from transforming during this procedure. When the taps have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any type of old sealing compound.
Prior to proceeding to fit the new taps, compare the pipe links on the old faucets to the new taps. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Suitable New Taps
If the tails of the new faucets are plastic, then you will require a plastic port to stop damages to the string. One end of the port fits on the plastic tail of the tap as well as the other end offers a connection to the current supply pipes.
If you need to fit a monobloc, then you will certainly require reducing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, place the faucet in the installing hole in the bath/basin guaranteeing that the washers are in area in between the faucet and also the sink. Secure the faucet in place with the supplier offered backnut. As soon as the tap is firmly in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with regular faucet connectors. The previous kind needs to be connected to the faucet ends initially, tightening just by hand. The supply pipes can later on be attached to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Mounting the Tub
Making use of the two wood boards under its feet, position the bathtub in the required position. The wooden boards are useful in evenly spreading out the weight of the bath tub over the location of the boards as opposed to focusing all the weight onto 4 little factors.
The following goal is to make certain that the bath tub is leveled all round. This can be achieved by inspecting the level and also changing the feet on the bathtub up until the spirit level checks out level.
To install taps, fit the bottom of the furthest flexible faucet port to the proper supply pipe by making a compression join; then do the same for the other tap.
Activate the water system and examine all joints and new pipework for leakages and also tighten them if necessary. Fill up the tub as well as additionally inspect the overflow electrical outlet as well as the typical electrical outlet for leakages.
Lastly, repair the bath paneling as defined in the producer's instruction manual. Tiling and also sealing around the bathtub ought to wait till the bath tub has actually been utilized at least once as this will resolve it right into its last placement.
Getting ready for the Installation
First of all, the sustaining framework provided with the bathroom ought to be fitted (if needed) according to the producer's instructions. Next, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is very important to ensure that if the faucet features a plastic washing machine, it is fitted between the bathroom and also the faucets. On a plastic bath, it is additionally sensible to fit a sustaining plate under the faucets system to avoid strain on the tub.
Fit the flexible tap adapters to the bottom of both faucets using 2 nuts as well as olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. See to it you make use of every one of the provided washing machines.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath need to currently prepare to be fitted in its last setting.
Tiling Around the Tub
In the location where the bathroom satisfies the tile, it is essential to secure the accompanies a silicone rubber caulking. This is necessary as the installation can move sufficient to fracture a rigid seal, causing the water to pass through the wall surface in between the bath and also the tiling, causing issues with dampness and possible leaks to the ceiling below.
You can choose from a variety of coloured sealants to assimilate your components as well as installations. They are sold in tubes as well as cartridges, and also are capable of securing spaces approximately a size of 3mm (1/8 inch). If you have a larger void to load, you can load it with twists of drenched paper or soft rope. Bear in mind to always fill the bath tub with water before sealing, to enable the activity experienced when the bathtub is in use. The sealant can crack relatively early if you do not take into consideration this activity before sealing.
Conversely, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise easily readily available on the marketplace. It is advisable to fit the floor tiles utilizing waterproof or water resistant sticky and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I stumbled upon that piece of writing on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround when perusing the internet. For those who appreciated our blog entry plz do not forget to share it. Many thanks for your time spent reading it.
Rapid response assured.